Home > High Tensile Wire Mesh > High Tensile Rockfall Mesh

High Tensile Rockfall Mesh

  • High Tensile Galvanized Wire Mesh
  • High Tensile Steel Mesh
  • High Strength Steel Wire Mesh
  • High Tensile Steel Wire Mesh
  • High Tensile Wire Mesh
  • High Tensile Rockfall Mesh
  • 3.5‘’*3.5‘’ High Tensile Wire Mesh
  • Tecco High Tensile Steel Mesh
  • Active Wire Mesh
  • High Tensile Active Wire Mesh
  • High Tensile Anchored Mesh
  • Anchored Mesh
  • Anchored Wire Mesh
  • Slope Stabilization Mesh System


Product Description

Components:

The HIGH TENSILE ROCKFALL MESH system consists of four main components that are carefully coordinated with each other:

 

1. HIGH TENSILE ROCKFALL MESH 

High Tensile Rockfall Mesh is made of high-tensile steel wire with an ultimate tensile strength of 1770 N/mm2.

-Product Description:

1. wire diameter:3mm/4mm/2mm

2. high tensile strength 1770Mpa,1370Mpa, 900Mpa

3. mesh size:83*143mm, 122*177mm, 62*95mm etc

4. Mesh shape:diamond

5. Material:high tensile steel wire

6. Corrosion protection:super coating

7. Coating: no less than 150g/m2

8. Breaking load of single wire:12.5KN

9. Tensile strength:110KN/m

 

High Tensile Rockfall Mesh standard roll:

Mesh edges knotted

Roll width:2.3m-3.5m

Roll length:110m-30m

Weight:1.75kg/m2

 

2. SOIL OR ROCK NAILS

Adapted to the local soil and rock static requirements, the HIGH TENSILE ROCKFALL MESH can be anchored in accordance with our dimensioning concept with commercial soil or rock nails.The main anchors of the system are installed in a grid typically from 6.6 to 16.4 ft (2.0 to 5.0m)horizontal and vertical spacing.Actual spacing depends upon the results of site analysis and modeling. Anchor consist of commercially available steel bars ranging from 1.0 to 1.25 ft (25 to 32mm). Selfdrilling grout injection anchors are also permitted.Additional anchors may also be used to provide added support at boundaries and in low points and hollows.

 

3. SPIKE PLATES

Rigid spike plates that are reinforced with ribbing ensure optimal load transmission from soil or rock anchors to the HIGH TENSILE ROCKFALL MESH. These plates are placed over the anchor heads and tightened to pre-tension the mesh onto the slope. The plates are galvanized and have dimensions of 13.0''*7.5"*0.4"(330mm*190mm*10mm).

4. CONNECTION CLIPS

The connection clips high-strength steel wire connection clips enable mesh sections to be joined without overlapping and still guarantee one hundred percent transfer of forces. These claw are hot dip galvanized and consist of 0.25"(6mm) thick steel spiral.

5. SOIL OR ROCK NAILS

Adapted to the local soil and rock static requirements, the HIGH TENSILE ROCKFALL MESH can be anchored in accordance with our dimensioning concept with commercial soil or rock nails.The main anchors of the system are installed in a grid typically from 6.6 to 16.4 ft (2.0 to 5.0m)horizontal and vertical spacing.Actual spacing depends upon the results of site analysis and modeling. Anchor consist of commercially available steel bars ranging from 1.0 to 1.25 ft (25 to 32mm). Selfdrilling grout injection anchors are also permitted.Additional anchors may also be used to provide added support at boundaries and in low points and hollows.

Related Products

Inquiry Information

  • *Subject:

  • *Content:

  • *Telephone Number:

  • *Your E-Mail:

  • *Confirm Text:

    captcha

Contact Us